Polywater CG-13 Type CG Cold Galvanizing Spray: Specs, Coverage and How to Apply

November 12, 2026

Polywater CG-13 Type CG Cold Galvanizing Spray: Specs, Coverage and How to Apply

Polywater Type CG is a cold galvanizing spray for repairing cut or damaged galvanized steel and for priming bare ferrous metal. The coating is 90% pure zinc, so it protects the same way hot dip galvanizing does: the zinc sacrifices itself before the steel underneath rusts. It comes as catalog number CG-13, a 16 fl. oz. aerosol can.

Safety: The SDS classes Type CG as an extremely flammable aerosol under pressure. Keep it away from heat, sparks and flame, and use it outdoors or with good ventilation.

Polywater Type CG at a Glance

What Polywater says the product is and does.

FeaturePolywater specification
Zinc content90% pure zinc in the dry film
ProtectionSacrificial galvanic action plus a continuous zinc barrier
MetalsWorks on all ferrous-based metals
UsePrimer or touch-up, and weld coating
PlasticsCompatible with plastics
NozzleMinimizes drips and resists gumming and plugging
FinishGray, matte

CG-13 Catalog Number and Packaging

Type CG is sold as one catalog number.

Catalog numberPackageUnits per case
CG-1316 fl. oz. (475 mL) aerosol can with spray nozzle12

Coating Properties and Coverage

Values are from the Polywater Type CG technical brief.

PropertyValue
Coverage10 to 15 ft² (0.9 to 1.4 m²) per can
Dry film thickness1.5 to 3.0 mils (0.038 to 0.075 mm)
Dry time to handle (70 °F / 21 °C)30 to 40 minutes
Dry time to topcoat (70 °F / 21 °C)2 to 3 hours
Solids by weight79 ±2%
Solids by volume40 ±1%
Dried density19.9 lb/gal (2.38 g/mL)
WeldableYes
Temperature resistance250 °F (121 °C) sustained, 300 °F (149 °C) intermittent

Specifications and Test Results

Polywater lists the following military specifications and ASTM results for Type CG.

Specification or testWhat it covers
P-26915A Type 1, Class APrimer for steel (USAF)
P-46105Weld-through zinc rich primer
DOD-21035AZinc rich galvanize repair
ASTM B117 salt fogPasses 1,000 hours
ASTM D2247 humidityPasses 500 hours

Where to Use Cold Galvanizing Spray

Polywater recommends Type CG for these utility and industrial uses.

UseExamples
Pole line hardwareFasteners, brackets, threads, cut steel apparatus
EnclosuresBreaker panels, meter boxes, transformer and sectionalizing cabinets
StructuresUtility poles, conduits, guard rails, safety rails, ladders, fencing
EquipmentUtility trailers
WeldsWeld coating and weld-through primer

How to Apply Type CG

Follow Polywater's steps for a coating that lasts.

StepWhat to do
1. Prepare the surfaceKeep it dry and free of oil, grease and rust bloom. Remove weld splatter and grind rough welds smooth. For new steel, Polywater calls for blast cleaning per SSPC SP 6-63 to a maximum profile of 1.5 mils. For painted surfaces, spot blast exposed areas. Power tool brushing is fine for minor touch-ups.
2. Check conditionsAir temperature must be above 50 °F (10 °C), and the surface at least 5 °F (3 °C) above the dew point.
3. Shake the canShake vigorously until the agitator moves freely.
4. SprayUse light, even strokes from about 18 inches (1/2 meter) away. Apply several thin coats with 15 minutes of drying time between coats.
5. Let it dryLet the final coat dry thoroughly, up to 24 hours.
6. Clear the nozzleInvert the can and spray until only air escapes, so the nozzle does not clog.

Topcoats and Limits

Type CG can be used alone or under a topcoat, with a few limits.

TopicPolywater guidance
Compatible topcoatsCatalyzed epoxies, coal tar epoxy, vinyl, phenolics, acrylics, chlorinated rubbers and urethanes
Topcoats to avoidAlkyd-based topcoats
Atmospheric serviceTopcoat outside a pH range of 6.5 to 8
ImmersionNot recommended for acids or alkalis, or for continuous fresh or salt water immersion without a topcoat. Avoid total immersion in solvents.

Frequently Asked Questions About Polywater CG-13

What is Polywater CG-13?

It is the catalog number for Polywater Type CG Cold Galvanizing Spray, a 90% zinc aerosol for repairing galvanized steel and priming ferrous metal.

How much does one can cover?

Polywater lists 10 to 15 ft² per can at a dry film thickness of 1.5 to 3.0 mils.

How long does it take to dry?

About 30 to 40 minutes to handle and 2 to 3 hours before topcoating, at 70 °F. Polywater says the final coat can take up to 24 hours to dry thoroughly.

Can I weld over it?

Yes. Type CG is weldable and is listed to P-46105 as a weld-through zinc rich primer.

Does it repair cut or damaged galvanized steel?

Yes. Polywater lists it for repairing cut, damaged or exposed galvanized surfaces, and it is listed to DOD-21035A for zinc rich galvanize repair.

What color is it?

Gray with a matte finish.

Does it need a topcoat?

Not always, but Polywater says to topcoat for atmospheric service outside a pH range of 6.5 to 8, and for continuous water immersion.

Where to Buy Polywater CG-13

Powertech Associates supplies American Polywater products. Order online: Polywater CG-13 Cold Galvanizing Spray. For case quantities or other questions, contact Powertech Associates at info@powertech-upsc.com or (860) 678-8772. You can also see the Type CG page on the Polywater website.

Last updated: November 2026.

Interested in this product?

Contact us, request a quote, or order online.