TE AMPACT Installation Tools: Small and Large Tools, EZLoad, Cartridges and Hot-Stick Accessories

November 2, 2026

TE AMPACT Installation Tools: Small and Large Tools, EZLoad, Cartridges and Hot-Stick Accessories

AMPACT taps are installed with a powder-actuated tool, and every part of the system is color coded so the tap, the cartridge and the tool match. This guide lines up the TE Connectivity AMPACT installation tools, the EZLoad tool, cartridges, clips, hot-stick accessories and the other small parts crews need on the truck. Part numbers and specs are from the TE Connectivity North America Power Transmission and Distribution product catalog (2025).

AMPACT Tools: Small and Large

Two tools cover the AMPACT tap line. Pick the one that matches the color of the tap.

Catalog numberDescriptionConnects
69437Small AMPACT Tool, for red, white and blue coded tapsAluminum wire combinations #8 to 350 kcmil
69611Large AMPACT Tool, for yellow coded taps onlyAluminum wire combinations 336.4 to 1192.5, up to 3000 MCM AMPACT EL tap connectors

The tools are lightweight and powder actuated, so they take little effort to use. They install and remove taps in confined spaces and adapt to standard hot-stick use. Conductor applications are imprinted on the tap packages, and packages and labels are color coded to match the taps, tools and cartridges.

Using the AMPACT Tool with a Hot Stick

TE shows four steps for installing a tap with the tool on a hot stick.

StepWhat to do
1. Position the clampPlace the piggyback clamp on the wire, with the "C" member hooked onto the wire. TE shows the clamp 6 to 10 inches from the end of the wire.
2. Place the wedgeSet the wedge in the "C" member.
3. Clamp the tool over the tapUse the correct size tap and wires, with the wedge inserted halfway. The cartridge color matches the tap color. Keep the coupling tight against the wedge and the "C" member in the proper notch.
4. Fire the toolStrike the end of the geared breech cap assembly with a rubber hammer to complete the tap.

AMPACT Tool Replacement Parts

These parts rebuild or refresh the small and large tools.

Catalog numberDescription
69633-2Large tool head
47667-8Small tool head
69612Universal power unit
308967-1Breech assembly
314196-1Breech cap assembly (3-piece)
5-304668-3Retaining spring

AMPACT EZLoad Tool and Parts

The EZLoad is a powder-actuated tool with a lock and load design. It hinges on the power unit, so it opens and closes easily to replace cartridges. It comes in a small head and a large head, and the same interchangeable power unit is used in both.

Catalog numberDescription
1443413-1AMPACT EZLoad small tool
1443414-1AMPACT EZLoad large tool
1443412-1AMPACT EZLoad power unit
1443413-2AMPACT EZLoad power adapter
1443514-1Hot-stick adapter kit (includes piercer pin guide and cover)
1443470-1Hot-stick adapter with power unit
1443442-1EZLoad cleaning tool
1443448-1Tool repair kit (includes piercer pin guide, piercer pin and grub screw)
69610-2Hot-stick kit for the EZLoad tool

AMPACT Cartridges

The cartridges are molded of weatherproof polyethylene and packed with propellant and primer. The color tells you the strength of the powder charge and matches the color code of the tap it installs.

Catalog numberColor
69338-5White
69338-2Red
69338-1Blue
69338-4Yellow

Take-Off Clips and Auxiliary Platform

Take-off clips are used to remove AMPACT taps. TE refers installers to Customer Manual 409-2106 for tap removal.

Catalog numberDescription
69685-1Take-off clip for blue coded taps (and white coded copper taps)
69684Take-off clip for red coded taps
69947Take-off clip for Type II white coded taps
69847Take-off clip for yellow coded taps
306814-3Auxiliary platform

The 69437 small tool includes take-off clips 69947 and 69685-1, and the 69611 large tool includes take-off clip 69847. The auxiliary platform 306814-3 is required to install red coded standard taps with the small AMPACT tool.

Hot-Stick Accessories

The hot-stick kit lets linemen work in line with the conductors instead of across them. TE says it handles AMPACT taps and stirrups from No. 8 to 556.5-27/7 ACSR, and with additional components, conductors up to 1192.5-45/7 ACSR. The accessories are ordered separately from the hot-stick kit, and are required for taps and stirrups in the 795.0 to 1192.5 kcmil range.

Catalog numberBAT hot stick accessoryTap size
2480674-1Wedge holder, small4/0 series
2401416-1Wedge holder, medium336 to 556 series
2401815-1Wedge holder, large795 series
306350-2"C" holder4/0 to 795 series
69816Piggyback clamp4/0 and 336 to 556 series
69883Piggyback clamp795 series
69674Hammer4/0 to 795 series
Catalog numberFired-on hot stick accessory
306348-1Fired-on wedge holder
306350-2"C" holder
69900Combination "C" and wedge holder
69816Piggyback clamp, #8 AWG to 556 ACSR
69883Piggyback clamp, 556 ACSR to 1192.5 ACSR
306347-1Geared breech standard tool
1443514-1Geared breech EZLoad
69833-190 adapter
306349-2Small test holder
306349-1Large tool holder
69674Hammer

Cleaning Tools, Inhibitor Compound and Bags

These smaller items keep the tools clean, protect the connection and carry the kit.

Catalog numberDescription
314199-1Universal cleaning tool
1443442-1EZLoad cleaning tool
80665-3Aluminum inhibitor compound, 8 oz. (236 mL) plastic bottle
80665-2Aluminum inhibitor compound, 1 qt (0.95 L) can
561118-12-hole NEMA interface hinge to protect against corrosion between dissimilar metals
608338-1Accessory bag, open type, brass snap-on swivel hook, white canvas, 12.5 in. (317.4 mm) tall, 7 in. (177.8 mm) diameter
607501-1Accessory bag, open type, brass snap-on swivel hook, 12.5 in. (317.4 mm) tall, 7 in. (177.8 mm) diameter
608877-1AMPACT tool kit box

Frequently Asked Questions About AMPACT Tools

Which AMPACT tool do I need?

Use the small tool, 69437, for red, white and blue coded taps, and the large tool, 69611, for yellow coded taps only.

What do the cartridge colors mean?

The color shows the strength of the powder charge and matches the color code of the tap. Use the cartridge that is the same color as the tap.

Can AMPACT taps be installed with a hot stick?

Yes. The tools adapt to standard hot-stick equipment, and TE offers a hot-stick kit with wedge holders, "C" holders, piggyback clamps and a hammer, ordered separately.

How are AMPACT taps removed?

With take-off clips matched to the tap color. TE refers to Customer Manual 409-2106 for removal instructions.

What is the EZLoad tool?

It is a powder-actuated AMPACT installation tool with a lock and load design, available with a small or a large head on the same interchangeable power unit.

Do the tools come with take-off clips?

The 69437 small tool includes take-off clips 69947 and 69685-1, and the 69611 large tool includes clip 69847.

Where to Buy AMPACT Tools

Powertech Associates supplies TE Connectivity AMPACT products. Order online: EZLoad large tool (1443414-1), blue take-off clip (69685-1) or AMPACT cleaning tool (314199-1). For the other tools, cartridges and accessories, or to match them to your taps, contact Powertech Associates at info@powertech-upsc.com or (860) 678-8772.

Last updated: November 2026.

Interested in this product?

Contact us, request a quote, or order online.