Polywater P7-12 Type P7 Penetrating Oil: Specs, Uses and Safety

November 13, 2026

Polywater P7-12 Type P7 Penetrating Oil: Specs, Uses and Safety

Polywater Type P7 is a penetrating oil made for electrical and communications work. One spray displaces moisture, protects metal from rust and lubricates, so a crew does not need a separate product for each job. It comes as catalog number P7-12, a 16 fl. oz. aerosol can, sold in cases of 12.

Safety: The SDS classes P7 as a flammable aerosol under pressure. Keep it away from heat, sparks and flame, and do not pierce or burn the can, even when empty.

Polywater Type P7 at a Glance

What Polywater says P7 does.

FeaturePolywater specification
Displaces waterSeals out moisture to prevent corrosion, and can drive moisture out of water-soaked equipment going back into service
PenetratesLoosens stuck metal parts in equipment and switchgear
ProtectsLeaves a protective film that extends the life of equipment and hardware
Non-conductiveThe protective film is non-conductive
Material safetyHarmless to most plastics, and safe on metal, paint and rubber

P7-12 Catalog Number and Packaging

Type P7 is sold as one catalog number.

Catalog numberPackageUnits per case
P7-1216 fl. oz. (475 mL) aerosol can with spray nozzle12

Specifications and Test Data

Values are from the Polywater Type P7 flyer and product page.

PropertyValue
Flash point (ASTM D93)100 °F (38 °C)
Initial boiling point245 °F (118 °C)
Specific gravity0.69
Dielectric strength (ASTM D877)13 kV
Water displacementTested to Mil-Spec C-16173E, with no rusting or mottling observed on the treated surface
Corrosion testCopper 110 and low carbon steel 1808 panels showed less than 5% oxidation after 3 months of environmental aging

Where to Use Type P7

Polywater lists these uses for P7.

UseExamples
Seized hardwareFreeing stuck pole line hardware, nuts and bolts
EnclosuresLubricating and protecting cabinets and enclosures
EquipmentMaintaining and lubricating equipment and motors, and loosening stuck parts in switchgear
LocksSpraying into lock tumblers
Water damageRestoring electrical or electronic systems damaged by water ingress

Handling and Storage

These points come from the Polywater Type P7 safety data sheet, revised October 9, 2025. Read the full SDS before use.

TopicSDS statement
HazardFlammable aerosol, Category 2. Pressurized container that may burst if heated.
Ignition sourcesKeep away from heat, sparks, open flames and other ignition sources. Do not spray on an open flame.
ContainerDo not pierce or burn, even after use.
ExposureDo not breathe dust, fume, mist, vapors or spray. Wash thoroughly after handling.
StorageProtect from sunlight. Do not expose to temperatures above 50 °C (122 °F).
Incompatible materialsStrong oxidizing agents and acids

Looking for a coating to repair cut galvanized steel? See Polywater CG-13 Cold Galvanizing Spray.

Frequently Asked Questions About Polywater P7

What is Polywater P7?

It is a multi-function penetrating oil that displaces water, prevents rust and lubricates, made for electrical and communications use.

Is P7 conductive?

Polywater describes the protective film it leaves as non-conductive, and lists a dielectric strength of 13 kV (ASTM D877).

Is it safe on plastics, paint and rubber?

Polywater says it is harmless to most plastics and safe on metal, paint and rubber. Because the claim says most plastics, Polywater tells users to run their own evaluation for the intended use.

Can it free seized pole line hardware?

Yes. Polywater lists freeing seized pole line hardware, nuts and bolts as an application, and says P7 penetrates quickly to loosen stuck metal parts.

Can it dry out wet equipment?

Polywater says P7 can drive moisture out of water-soaked equipment being returned to service, and lists restoring water-damaged electrical and electronic systems as a use.

What size does it come in?

One catalog number, P7-12: a 16 fl. oz. (475 mL) aerosol can, 12 cans to a case.

Is P7 flammable?

Yes. The SDS classifies it as a flammable aerosol, Category 2, in a pressurized container. Keep it away from heat and ignition sources.

Where is it sold?

Polywater sells P7 only in the United States and Canada.

Where to Buy Polywater P7

Powertech Associates supplies American Polywater products. Order online: Polywater P7-12 Penetrating Oil. For case quantities or other questions, contact Powertech Associates at info@powertech-upsc.com or (860) 678-8772. You can also see the Type P7 page on the Polywater website.

Last updated: November 2026.

Interested in this product?

Contact us, request a quote, or order online.